Connecting Rod Race Set
$132.95
1025-15
All PRODUCTS
New Products
Race set is made from 52100 steel and hardened. Set is a 3 piece set. Fitment: 1930 Harley Davidson VL 1931 Harley Davidson VL...
Connecting Rod Wrist Pin Bushing Set
$44.95
24335-36
All PRODUCTS
Best Sellers
Engine
New Products
.005 oversize bushings for piston pin. Set of two. *NOTE* Inside diameter must be reamed to proper size after installation. Measurements: Inner Diameter: 0.778...
Engine Pinion Shaft
$140.95
24005-37
All PRODUCTS
Pinion shaft is precision ground for correct fitment. Shaft includes plug. Fitment: 1937 Harley Davidson G 1937 Harley Davidson WL 1938 Harley Davidson G...
Hydraulic Tappet Assembly .005
$127.95
2461-1
All PRODUCTS
Engine
New Products
Jims big axle power glide hydraulic tappet only is .005 inch oversize for Shovelhead engines. Instructions: http://www.vtwinmfg.com/Instructions/10/10-0644.pdf Fitment: 1966 Harley Davidson FL 1967 Harley...
Hydraulic Tappet Assembly .005
$88.95
2464-1
All PRODUCTS
Best Sellers
Engine
New Products
Jims .005 oversize hydraulic tappet includes installed roller assembly. Order hydraulic unit and nuts separately. **NOTE: Tappet adjustment will make the pushrod tight. Wait...
Jims 3-Hole Crank Pin .001 Oversize
$106.95
23974-873
All PRODUCTS
Engine
Crank pin is .001 oversize on bearing diameter. Pin is heat treated 60-62RC to a case depth of .100. Crank pin has a 1.2505...
Jims 3-Hole Crank Pin .025 Shorter
$106.95
23961-41ST3
All PRODUCTS
Engine
Crank pin is heat treated 60-62RC to a case depth of .100. A special 180 oiling design will better lubricate the bearing diameter. Threads...
Jims 3-Hole Crank Pin with 180 Oiling
$103.95
23961-80AS
All PRODUCTS
Engine
New Products
Crank pin is made of 8620 steel with heat treating 60-62RC to a case depth of .100. A special 180 oiling design helps lubricate...
Jims Connecting Rod Race Set
$89.95
1046-36A
All PRODUCTS
Best Sellers
Engine
Rod race set is made from 52100 steel and hardened. Set of three. Measurements: Outer Diameter: 1.8185 inches Fitment: 1936 Harley Davidson EL 1937...
Jims Engine Sprocket Shaft
$84.95
24000-29
All PRODUCTS
Best Sellers
New Products
Sprocket shaft is machined and hardened to factory specifications. Fitment: 1929 Harley Davidson DL 1930 Harley Davidson DL 1931 Harley Davidson DL 1932 Harley...
Jims Hydrosolid Tappet Assembly Standard
$116.95
1800
All PRODUCTS
Engine
New Products
Jims big axle tappet assembly standard hydrosolid. Roller assembly installed and has a built in anti-pump device perform like a hydraulic from start up...
Jims M8 Low Profile Billet Tappet Block Kit Black Anodize
$240.95
6020
All PRODUCTS
Engine
New Products
Jims billet inchlow profile inch M8 tappet cover set feature a sleek new look but they are approximately 1/2 inch lower than stock making...
Jims M8 Low Profile Billet Tappet Block Kit Chrome
$256.95
6021.
All PRODUCTS
Engine
New Products
Jims billet inchlow profile inch M8 tappet block set feature a sleek new look but they are approximately 1/2 inch lower than stock making...
Jims Pinion Right Side Case Race .002
$113.95
24600-58B
All PRODUCTS
Engine
New Products
.002 oversize right side case race is machined and ground to factory specifications. Pinion bearing race features 360 oiling groove for 1993-up models. Case...
Jims Pinion Right Side Case Race .005
$196.95
24597-40
All PRODUCTS
New Products
.005 right side case race is machined and ground to factory specifications. Fitment: 1940 Harley Davidson UL 1941 Harley Davidson UL 1942 Harley Davidson...
Jims Pinion Right Side Case Race .005
$126.95
24601-40
All PRODUCTS
Engine
.005 oversize right side case race is machined and ground to factory specifications. Fitment: 1940 Harley Davidson FL 1941 Harley Davidson FL 1942 Harley...
Jims Pinion Right Side Case Race Standard
$117.95
24595-40
All PRODUCTS
New Products
Standard right side case race is machined and ground to factory specifications. Race has an outer diameter of 2.0015″ inch. Measurements: Inside Groove: .034...
Jims Pinion Right Side Case Race Standard
$116.95
24585-57
All PRODUCTS
Engine
New Products
Standard right side case race is machined and ground to factory specifications. race has an outer diameter of 1.7515″ inch. Fitment: 1957 Harley Davidson...
Jims Pinion Right Side Case Race Standard
$101.95
24599-58A
All PRODUCTS
Engine
Standard right side case race is machined and ground to factory specifications. Fitment: 1958 Harley Davidson FL 1959 Harley Davidson FL 1960 Harley Davidson...
Jims Pinion Right Side Case Race Standard
$110.95
24599-40
All PRODUCTS
Engine
New Products
Standard right side case race is machined and ground to factory specifications. Race has an outer diameter of 2.0015″ inch. Fitment: 1940 Harley Davidson...
Jims Powerglide Hydraulic Tappet Assembly Standard
$103.95
2456-1
All PRODUCTS
Engine
New Products
Jims power glide hydraulic standard tappet comes as a individual unit. Measures .8425 inch. Fitment: 1984 Harley Davidson FLT 1984 Harley Davidson FXR 1984...
Jims Powerglide II Hydraulic Tappet Assembly .005 Oversize
$115.95
1810
All PRODUCTS
Engine
New Products
Jims powerglide II is a hand honed hydraulic unit with increased load and lubrication capacities. Includes roller assembly .005 oversize. For Twin Cam or...
Jims Sprocket Left Side Case Race Standard
$121.95
24621-40
All PRODUCTS
Engine
Left side case race is machined and ground to factory specifications. Race has an outer diameter of 2.0015 inch. *NOTE: Left side cases accept...
JIMS TOOLS CAM BEARING INSTALL TOOL KIT HARLEY M8 17-26
$829.95
All PRODUCTS
New Products
TOOLS/SHOP
JIMS TOOLS CAM BEARING INSTALL TOOL KIT HARLEY M8 17-26 The Milwaukee-Eight® engine returns to the single camshaft design, which requires a new tool...
JIMS TOOLS CAM BEARING INSTALL TOOL KIT HARLEY TWIN CAMS 99-17
$639.95
3801-0160
All PRODUCTS
New Products
TOOLS/SHOP
JIMS TOOLS CAM BEARING INSTALL TOOL KIT HARLEY TWIN CAMS 99-17 Designed to press from the letter side of the inner cam bearing to...
JIMS TOOLS CAM CHAIN TENSIONER TOOL KIT 99-06 HARLEY TWIN CAMS
$179.95
DS-196196
All PRODUCTS
New Products
TOOLS/SHOP
JIMS TOOLS CAM CHAIN TENSIONER TOOL KIT 99-06 HARLEY TWIN CAMSÂ Designed to unload the pressure on the primary and secondary chain tensioners to...
JIMS TRANS SPROCKET MEGA NUT LOCK HARLEY DAVIDSON MODELS
$269.95
All PRODUCTS
HARLEY BELT DRIVE
HARLEY CHAIN DRIVE
New Products
JIMS TRANS SPROCKET MEGA NUT LOCK HARLEY DAVIDSON MODELS CHOOSE YEAR AND MODEL IN OPTIONS Includes machined clamping face tolerance, along with additional locking...
JIMS TRANSMISSION REBUILD KITS FOR HARLEY
$929.00
JMS-TRN-RBL-KTS-07-16
All PRODUCTS
HARLEY TRANS
New Products
JIMS TRANSMISSION REBUILD KITS FOR HARLEY
CHOOSE YEAR IN OPTIONS
tax and shipping included in canadaÂ
Right Side Case Race .005
$104.95
24587-39
All PRODUCTS
New Products
.005 oversize right side case race is machined and ground to factory specifications. Fitment: 1939 Harley Davidson G 1939 Harley Davidson WL 1940 Harley...
Right Side Case Race Standard
$117.95
24585-39
All PRODUCTS
Standard right side case race is machined and ground to factory specifications. Race has an outer diameter of 1.753 inch . Fitment: 1939 Harley...
Solid Tappet Assembly .005
$86.95
2467-1
All PRODUCTS
Best Sellers
Engine
New Products
Jims .005 oversize solid tappets can be only used with adjustable pushrods. Fitment: 1984 Harley Davidson FLT 1984 Harley Davidson FXR 1984 Harley Davidson...
Solid Tappet Assembly .005
$102.95
2476-1
All PRODUCTS
Engine
New Products
Jims .005 oversize solid adjustable tappet includes installed roller assembly Order adjuster screws and nuts separately. Fitment: 1948 Harley Davidson FL 1949 Harley Davidson...
Standard Case Race Left Side
$116.95
24610-39
All PRODUCTS
New Products
Left side case race is machined and ground to factory specifications. Race has an outer diameter of 1.753 inch. Fitment: 1939 Harley Davidson G...
Standard Hydraulic Tappet
$85.95
2462-1
All PRODUCTS
Best Sellers
Engine
New Products
Jims standard hydraulic tappet has an outer diameter of .731 inch. Tappets are without internals. Order hydraulic unit separately. **NOTE: Tappet adjustment will make...
Standard Hydraulic Tappet Assembly
$122.95
2459-1
All PRODUCTS
Engine
New Products
Jims big axle power glide tappet assembly. Tappets have an outer diameter of .731 inch and are for Shovelhead engines. Instructions: http://www.vtwinmfg.com/Instructions/10/10-0642.pdf Fitment: 1966...
Standard Solid Tappet Assembly
$100.95
2465-1
All PRODUCTS
Engine
New Products
Jims standard solid tappets can only be used with adjustable pushrods. Tappet has an outer diameter of .8425 inch. Fitment: 1984 Harley Davidson FLT...
